Programming Your Overhead Door Odyssey 1000: A Comprehensive Guide

The Overhead Door Odyssey 1000 opener is known for its advanced features, including CodeDodger® technology, designed to enhance security and convenience. Programming your remote, HomeLink system, or wireless keypad can seem daunting, but with the right instructions, it’s a straightforward process. This comprehensive guide provides step-by-step instructions for various programming scenarios, ensuring you can effortlessly manage your garage door opener.

Understanding CodeDodger® Technology

The Overhead Door Odyssey 1000 opener stands out thanks to its advanced CodeDodger® technology, which enhances security and convenience. CodeDodger® technology adds an extra layer of security, protecting your home from potential threats. Enjoy the added peace of mind and enhanced performance of your Overhead Door Odyssey 1000 opener.

Programming a Remote to CodeDodger® 1 Mode

Before programming your HomeLink system or other devices, you may need to program one of the buttons on your Overhead Door remote into CodeDodger® 1 mode. Here’s how:

Enter CodeDodger® 1 Mode: Press and hold one of the unused buttons for 10 seconds. You will see the LED change from green to green and red.
Confirm the Change: Once you see green and red, release the button and press the same button two times to confirm the change to CodeDodger® 1. You should now see the LED being red when activated.

Programming HomeLink to Your Garage Door Opener

Integrating your garage door opener with your vehicle's HomeLink system offers unparalleled convenience. Please refer to the owner’s manual for your vehicle for the specific instruction on programming home link to the garage door opener. Since the instructions will vary by vehicle manufacturer please take the time to review carefully as the instruction steps may vary from this video. Here's a detailed guide:

Clear HomeLink Memory (First-Time Training): For first time training press and hold the two outer HomeLink buttons, releasing only when the HomeLink indicator light begins to flash, usually within 20 seconds. This clears the HomeLink memory and is now ready for programming. You do not perform this step on training the additional HomeLink buttons to other garage door openers or other HomeLink devices.
Enter Training Mode: Press the appropriate HomeLink button (1, 2, or 3) which you want to train and keep holding it until the indicator light starts flashing slowly. Once the indicator light starts flashing slowly release the button. HomeLink is now in training mode.
Locate the Transmitter Unit: For most vehicles you’ll be programming the remote a HomeLink inside the vehicle. For this vehicle the instructions locate the transmitter unit to be train near the right headlight. Please refer to the instructions in the owners manual or downloaded from www.homelink.com for this vehicle.
Synchronize with the Remote: Hold the original remote between 3 to 5 inches from the location at the transmitter. In this case the right headlight. Now press and hold the button on your original remote that is programmed to CodeDodger® 1 while keeping your hazard warning lights in view. For this vehicle the hazard warning lights will blink 3 times indicate that the training has been successful. If the training time exceeds 5 minutes the cars hazard warning lights will blink once in you’ll need to repeat steps 2 through 5.
Finalize Training: Return to the car and press and hold the train HomeLink button and observe the indicator light.
Engage the Learn Button: Move to the garage door opener powerhead and find the programming buttons.
Enter Main Menu: Start by entering the main menu press and hold the square button until you see the long and short blue LED. Release and you will see the short blue LED only.
Enter Programming Menu: To enter the programming menu press and release the square button you should see the short blue LED turn to a long purple LED. Pick-up the remote for your Odyssey or Destiny unit and press the button that you’ve already program to the powerhead.
Test the Connection: Return to the vehicle and firmly press and hold the train HomeLink button for 2 seconds and release. Repeat the press hold really sequence for 2 seconds again. The third press hold really sequence will activate the garage door opener.

Programming CodeDodger® Remotes

The Overhead Door Odyssey 1000 system supports both CodeDodger® 1 and CodeDodger® 2 remotes. Here’s how to program each type:

Read also: Comprehensive Guide to Programming

Programming a CodeDodger® 2 Remote

Enter Programming Menu: To program the Code Dogger two remote, first press and hold the program set button. Then press the program set button again to select the remote program menu.
Program the Remote: Press and release your desired remote button, press and release the remote button again and finally press and release the remote button the final time to operate the door.

Programming a CodeDodger® 1 Remote (Requires a Programmed CodeDodger® 2 Remote)

To program a Code Dodger one remote you must have a code dodger two remote available and already programmed.

Enter Programming Menu: To begin programming the code dodger one remote first press and hold the program set button then press the program set button again to select the remote program menu.
Synchronize Remotes: Press and release the already program button on the code dodger 2 remote. Then press and release the desired button on the code dodger 1 remote. Press and release the button again and finally press and release the button to operate the door.

Programming a CodeDodger® Wireless Keypad

For keyless entry, programming a wireless keypad is essential. The process differs slightly between CodeDodger® 1 and CodeDodger® 2 keypads.

Programming a CodeDodger® 2 Wireless Keypad

Set the PIN: To program a Code Dodger two wireless keypad, first set the pin. To begin press and hold the program button and be up/down arrow buttons until the lights go out. then press three five seven program. Enter the pin and press the program button and wait for the lights to turn off, the pin is now set.
Enter Programming Menu on Powerhead: Next, on the power head press and hold program set to enter the programming menu. Then press the program set button again to enter the remote program menu.
Synchronize Keypad and Powerhead: On the wireless keypad enter your pin number and press the up down arrow button once. Then press the up down arrow button again. Then press again to operate the unit.

Programming a CodeDodger® 1 Wireless Keypad

Initialize the Keypad: We first start with the CodeDodger one wireless keypad. Press and hold the program key, the number-6 key, and the up/down arrow key in order. When all of the lights go out on the keypad release all three buttons.
Set the PIN: Now you should see the LED flashing at a rate of one flash per second. Now enter your pin that you determined. Your pin should be between three to eight digits. Then press the program button. You should see the red LED flash two times then go out as confirmation.
Enter Main Menu on Powerhead: Move to the power head start by entering the main menu. Press and hold the square button until you see the long and short blue LED.
Enter Programming Menu on Powerhead: Now to enter the programming menu press and release the square button you should see the short blue LED turn to a long purple LED pick up the remote for your Odyssey or Destiny unit and press the button that you have already programmed to the power head.
Synchronize Keypad and Powerhead: Enter the pin that you have selected. Then press the up down arrow button. You will see the LED lights on the powerhead change from a flashing long and short purple to a solid long and short purple. Now press and release the up/down arrow key one more time. You will see the LED change from solid long and short purple to solid long and short blue. This confirms the connection between the CodeDodger one wireless keypad to the powerhead. By pressing the up/down arrow one more time you will see the Odyssey or Destiny opener start to move.

Adjusting Speed Settings

The Overhead Door Odyssey and Destiny openers feature adjustable speed settings for both opening and closing, allowing you to customize the operation to your preference. There are three speed settings for both the open and closed directions for these openers. The factory setting for the speeds is the maximum speed for both open and closed.

Enter Main Menu: Press and hold the square button until you see the long and short blue LED release and you will see the short blue LED only.
Navigate to Speed Programming: Press the up arrow with the plus sign two times and the long and short blue LED will appear press the square button to enter the speed programming menu you will see the short blue LED flash three times then show the current speed setting for the up travel or open speed. The current speed for this unit is the maximum which is shown by the solid red long and short LEDs.
Adjust Open Speed: Now press the down arrow one time and you will see the speed setting change from red LEDs maximum speed to purple LEDs medium speed. Press the down arrow one more time and you will see the speed setting change from purple LEDs medium speed to blue LEDs slow speed. Now we will press the up arrow one time and move the open speed to medium setting the purple LED appears. We will press the square button to confirm that we want medium for the open speed. You will see confirmation of the long LED flash blue three times.
Adjust Close Speed: The close or down speed level will be shown which is maximum speed both long and short red LEDs. Now press the down arrow or minus key one time and this changes the close or down speed to purple LEDs for medium speed. You can continue to press the down arrow to slow speed which is blue or the up arrow button one time to take this back to maximum close speed red LED. We will press the square button to confirm that we want medium speed. Both LEDs will flash blue to confirm it is set.
Test and Confirm: When changing the speed during installation please press the remote or wall console and visually confirm this is the desired speed.

Important Considerations Before Programming

Please be sure that your Odyssey or Destiny opener is installed, limits are set, force profile has been set and you have programmed one button on the new remote to the power head.

Programming a CodeDodger® 1 Remote to the Power Head

Enter Main Menu: Start by entering the main menu, press and hold the square button until you see the long and short blue LED release and you will see the short blue LED only.
Enter Programming Menu: Now to enter the programming menu press and release the square button. You should see the short blue LED turn to a long purple LED. Pick up the remote for your Odyssey or Destiny unit and press the button that you have already programmed to the power head this opens the window to allow programming a CodeDodger 1 remote to your Odyssey or Destiny opener. You should see the LED lights on the power head turn to a flashing long and short purple.
Connect the CodeDodger® 1 Remote: Now we need to finish the connection to the CodeDodger 1 remote. Press the button on the CodeDodger 1 remote that you wish to program to the Odyssey or Destiny power head. You will see the LED lights on the power head change from a flashing long and short purple to a solid long and short purple. Now press and release the button on the CodeDodger 1 remote one more time. You will see the LED change from solid long and short purple to salted long and short blue this confirms the connection between the CodeDodger 1 remote to the power head by pressing the button on the CodDodger 1 remote one more time. You will see the Odyssey or Destiny opener start to move.

Troubleshooting Tips

When it comes to managing your garage door opener, addressing Overhead Door Odyssey 1000 remote programming issues is often a straightforward process. Simply checking the LED indicator light on the motor head can reveal the source of the problem.

Read also: Programming Chamberlain Openers

Need Further Assistance?

If you're struggling with remote programming or misplaced instructions, fear not! If you need further assistance or have any questions, don’t hesitate to reach out. If challenges persist, reach out to us at Overhead Door Company of Central Jersey for expert assistance. We're dedicated to resolving any concerns you may have.

Read also: The Open Door Concept

tags: #overhead #door #odyssey #1000 #learn #button